影响丁基胶涂布机的因素

影响丁基胶涂布机的因素

影响丁基胶涂布机的因素主要有原材料的选用和生产制造工艺。其中原材料的质量将直接影响丁基胶涂布机的质量和使用寿命。目前国内丁基胶涂布机主要有三种:槽铝式单道密封、槽铝式双道密封、复合密封胶条式丁基胶涂布机。槽铝式单道密封因其密封性差,易进潮气,导致玻璃结露、结霜,使用寿命短,已逐渐被淘汰。双组份打胶机

The main factors that affect the butyl rubber coating machine are the selection of raw materials and the manufacturing process.. The quality of raw material will directly affect the quality and service life of butyl rubber coating machine.. At present, there are three main types of domestic butyl rubber coating machine: trough aluminum type single channel sealing, groove aluminum sealing, compound sealing tape type butyl rubber coating machine. Aluminum channel type single seal because of its poor sealing performance, easy to enter moisture and lead to a glass of dew and frost, short service life, has been eliminated gradually.

丁基胶涂布机的原材料主要包括玻璃、铝条、插角、丁基胶、双组份聚硫胶或有机硅硐胶、干燥剂、复合密封胶条。

The raw materials of the butyl rubber coating machine mainly include glass, aluminum, plug angle, butyl rubber, double component of the sulfur rubber or silicone rubber, desiccant, composite sealant.

一、玻璃的选用

Selection of glass

1、制造丁基胶涂布机的原片玻璃可以是无色浮法玻璃、镀膜玻璃、钢化玻璃、夹层玻璃等。应避免使用普通平板玻璃,普通平板玻璃的透明度及强度均达不到要求。上述玻璃原片必须符合相应标准要求,经检验合格后才能使用。

1, manufacturing butyl rubber coating machine of the original piece of glass can be colorless float glass, coated glass, tempered glass, laminated glass, etc.. Should avoid the use of ordinary flat glass, ordinary flat glass opacity and strength are not required. The above glass pieces must meet the corresponding standards, and can be used after the inspection..

2、不同厂家不同批次的玻璃在切割前应首先检查有无色差,将色差较大的玻璃分别用于不同的工程或不同的建筑立面中。

2, different manufacturers of different batches of glass in the cutting should be the first check before the color, the larger the larger glass were used in different projects or different building facades.

3、玻璃切割尺寸应按图纸要求严格执行,同时操作人员应注意玻璃表面,不得有划伤、气泡等明显缺陷。

3, the glass cutting size should be strictly according to the requirements of the drawings, while the operator should pay attention to the surface of glass, not scratches, bubbles and other obvious defects.

二、铝条、插角的选用

Two, aluminum, insert angle of choice

1、铝条的厚度应在0.30mm~0.35mm之间,厚度应均匀一致,透气孔分布均匀。铝条须经阳极氧化处理或去污处理,一定要选用质量好、档次高的产品,提高铝条利用率。

1, the thickness of the aluminum should be between 0.30mm ~ 0.35mm, the thickness should be uniform, uniform distribution of air hole. Aluminum strip by anodic oxidation or decontamination, must choose good quality, high grade products, improve the utilization of aluminum.

2、插角尺寸要选好,表面要擦干净。

2, angle size to choose, the surface to clean.

三、干燥剂

Three, desiccant

There are three main types of desiccant used in the present use of butyl rubber coating machine: 1. The absorption ability of volatile matter is good; 2, the adsorption capacity of inert gas is lowest; 3, ordinary molecular sieve. Users should be based on their own needs to the manufacturer to consult, choose the right molecular sieve. At the same time, the molecular sieve also has the appropriate size (1mm ~ 1.5mm) and the hardness.. The use of molecular sieve environment to dry, to avoid moisture and long time exposed, to ensure that butyl rubber coating machine

BACK PAGE